AUTOMATIC CALCULATION TABLE TO DRAFT A FITTED BODICE BASE  PRINT BODICE PATTERN 
Measurements 
Back drafting 
Front drafting
half neck circumference 
Middle of the back line A:N 
Supplementary  value 
half bust circumference 
Neck line  А:А1
Supplementary point of the dart opening  P:D 
half underbust circumference 
Bottom line  N:N1
Top of neckline  D:M 
half waist circumference 
Middle of the front line  connect A1 and N1 
Width of neckline  V:L
 half hip circumference 
Bust line position  A:G
Depth of neckline  V:U
half the back width 
Bust line  G: G1
From V along bisector  7
back length to the waist 
Length of back to waist  A: T 
Front shoulder length 
back shoulder height 
Waist line  T:T1
Shoulder length to the first dart line  L:O 
shoulder length 
Hip line position   T:B 
End of shoulder dart along bust line  O1:O2 1-1,5
garment length 
Hip line  B:B1
Length of the first line of shoulder dart Go down from O by 1 cm
Distance from waist to hips
Back width  A:E = G:C 
Connect the point O2 (1) and the point (1) with the point L
Increase for looser fit
Armhole width  C:P 
Direction point of shoulder cut  C:Sh
Half the armhole width C:K 
Connect Sh and M 
Width of the back neckline  A:P 
Shoulder dart  MF
Height of the back neckline  P:Yu 
Connect F and O2
Slant of the back shoulder  Е:Е1 1,5
Level both sides of the dart F:O2 =(1):O2 
Shoulder length  Yu:I 
The rest of the front shoulder  F:Ch 
Auxiliary point of the armhole  3 3,0
Auxiliary point of front armhole  2 2,0
Finishing the back armhole  connect I,3,K
Control point of armhole  P:Zh 
Side line position   C:g
Slant of front shoulder Ch:e  2,0
Draw a dotted line from g downward. Mark points t and z. Upward - g1
Segment Zh:e is divided in half and 1cm is marked 
Total waist darts ƩT
Finishing front armhole  Connect K - (2) - Zh - e1 - e
Opening of side dart  ƩB
Opening of side dart ƩB
Finishing back side line  t:t1
Finishing side line  t:t2
Back width along hips z:z1
Front width along hips line  z:z2
Waist dart posiiton  G:g2
Finishing bodice bottom  Т1:2 2,0
Draw a line downward from g2. Mark points v1, v
Opening of front dart ƩP
Opening of back dart  ƩCP
Finishing waist dart  a1a2=a1a3
Finishing waist dart  v1v2=v1v3
Tops of the darts from hip and bust line by 4-5 cm 
Tops of darts from hip and bust line in 4-5 cm 
  AUTOMATIC CALCULATION TABLE FOR SLEEVE CAP DRAFTNG  PRINT SLEEVE PATTERN 
Measurements 
Sleeve Cap drafting 
Circumference of the upper part of the arm 
Diameter of semi-circle  P1: P2 
Length of segment AP
Semicircle P2P1 with a radius  P2: P1
Length of segment A1P1
Posiiton of shoulder seam  P1:B
Total length of segments AP and A1P1
Measure segment 2 3 2 3
Diameter of semi-circumference of cap
Measure segment 1 3  1 3
Increase for looser fit
Difference between total length of segments 2 3, 1 3 and circumference of the upper part of the arm
Segment on the front  3 5
Segment on the back  1 4